Originally intended for use as a video connector in radar applications, the UHF coaxial connector was developed as a general-purpose unit for use in low-frequency systems from 0.6 - 300 MHz. Invented in the 1930s for use in the radio industry, UHF is an acronym for Ultra High Frequency because 300 MHz was considered high frequency at the time. They can be used when impedance matching is not required.
UHF connectors use threaded coupling. UHF connectors are economical and widely used because of their ease of assembly. The UHF solderable screw-in termination feature does not require a special crimping tool.
Specification
Mfr Part #
RHT-630-0115
Connector Type
Plug
Contact Type
Male Pin
Orientation
Straight
Contact Termination
Crimp
Mounting Type
Cable Mount
Fastening Type
Threaded
Impendance
50 Ohms
Frequency Max
300MHz
Shell Material
Copper Alloy
Insulation Material
PTFE
Contact Material
Brass
Contact Finish
Gold
Mfr Part #
RHT-630-0115
Connector Type
Plug
Contact Type
Male Pin
Orientation
Straight
Contact Termination
Crimp
Mounting Type
Cable Mount
Fastening Type
Threaded
Impendance
50 Ohms
Frequency Max
300MHz
Shell Material
Copper Alloy
Insulation Material
PTFE
Contact Material
Brass
Contact Finish
Gold
Features
View of UHF Connector
Can be Customized for unique material or performance requirements
The connector design was invented in the 1930s for use in the radio industry, and is a shielded form of the "banana plug". It is a widely used standard connector for HF transmission lines on full-sized radio equipment.
Large size threaded couplings are a robust design
The Ultra High-Frequency (UHF) connector is a threaded coaxial connector that was developed in the 1930s by engineers at Amphenol. The UHF connector has individual male and female radio frequency connectors that form a mated connection by thread coupling.
Crimp termination type provides a lower cost method of installation
This is a cost-effective, robust radio-frequency connector that is suitable for general-purpose use.
Not much I can really say about these crimp connectors. They aren't the super high end model, but when DYI comes into play, especially for the first time, they did just fine!
For the money, great value.
For the ease of use, well that's an experience thing. I was able to successfully put an end on a damaged feedline of mine, and the connection is working. I don't have super high end equipment to test and vet the feedline, but it works! To me, that is all that matters. No major loss and/or audible interference.
Review by
Cust
Posted on
Nickle plated rather than silver plated
Quality
80%
Price
80%
Nickle plated rather than silver-plated but not difficult to solder. Good fit and easy to work with. Yes, I would buy them again.
Review by
Jonathan Rimington
Posted on
Works as expected
Quality
80%
Price
80%
Bought these to use on RG8x and they worked just fine. Plan on buying another batch. If you are looking for crimp on PL259's these will meet your expectations. Ham Operators can be picky about the gear they use and should feel comfortable purchasing these. Costs is reasonable as well.
Review by
James W.
Posted on
worked well with rg8x
Quality
100%
Price
80%
Decent connector. Would buy them again.
Review by
Just Me
Posted on
Quality product
Quality
80%
Price
60%
Product quality as good as the more expensive brands and fit of parts made assembly of cable and connector simple
Review by
JOHN G
Posted on
Quick and precise
Quality
80%
Price
80%
It was exactly what we needed. Thank you
Review by
joyce ross
Posted on
I Thought the Crimp Barrel is a Bit Small (Revised)
Quality
80%
Price
80%
My initial thinking was that the crimp barrel is too small to allow pushing over the RG8X shield while still braided. I found that I had to undo the shield, smooth it out straight and trim the excess length to slide the barrel over the assembly before crimping. What I was doing was pushing the connector assembly too far. The inner shield tube was pushed under the shield and the outer sheath thus increasing the diameter the barrel had to go over.
After realizing my cockpit mistake, I find they are very good.. I like the small opening for the center conductor -- makes it easier to solder without slopping solder on the outside of the center pin. In spite of the issue, I've already bought another group of ten.
Review by
GJKJTexoma
Posted on
Decent PL-259's
Quality
80%
Price
80%
I'm a ham radio operator, so I know a thing or two about coax ends. I've probably soldered close to 100 over the course of my life so far. These are probably about "the best" lesser quality you'll find. Solder flowed easily and they fit well. Just don't overheat the tip, or you'll distort the teflon insert. Anyone know knows how to solder won't have this problem anyway.
Are these Amphenol PL-259 quality? Absolutely not. Far from it. Are these reasonable for lighter duty use? I feel like they are. I'll very likely order more.
Review by
Josh W
Posted on
Good for the price
Quality
80%
Price
100%
These are pretty good connectors for the price. They are not the best but far from the worst and will do the job. I did break one by tightening it down too much but that was pretty much my fault. If I were to do it again I would buy a few better quality ones for outside antenna connections and use these where they are easy to replace if needed. Overall I'm happy with the purchase.
Review by
Rick B
Posted on
Great customer service!!!
Quality
100%
Price
100%
I received my order and had been shorted some of the pieces,sent a message to the seller they sent it new set immediately. Very good customer service and very good quality product.
Review by
Manzo
Posted on
Excellent quality connector
Quality
100%
Price
100%
These crimp/solder connectors are perfect for the coax jumpers I needed. They crimp well and the gold center tip solders well. They even supply shrink tubing for strain relief. Very comparable to DX Engineering connectors for a much lower price
Review by
Bernard J. Meyers
Posted on
Great connectors at a great price.
Quality
100%
Price
100%
What can I say, a PL259 connector with an RG58 adapter that was a great price and came the next day. Looks great, and worked terrifically.
Review by
John K Hettler
Posted on
Quality crimp connectors
Quality
80%
Price
100%
Connectors worked fine with my RG-58 and crimper.
Review by
Venchant
Posted on
The fit is great
Quality
100%
Price
100%
Easy to install and crimp. All the parts fit very well with the RG58 cable.
Review by
rchamber
Posted on
Great PL 259 connectors
Quality
100%
Price
100%
This is my thrid order great connectors and fast service.
Review by
Wyatt Walker
Posted on
PL-259 connectors
Quality
100%
Price
100%
These connectors are great to work with, and are a perfect fit with RG8X coax cable.
Review by
Walter G. Carlington
Posted on
Great value.
Quality
80%
Price
80%
Been a ham for 60 + years and have put on a lot of PL-259's. For the money these do all you need. They're sturdy, take solder well, and the reducer fit RG8X coax just right. I don't have any experience on how they'd hold up in the weather, but for me they'd be good as I always weather proof my connectors.
